- ITC Category 1 Thermography Course
- ITC Category 2 Thermography Course
- ITC Category 3 Thermography Course
Produkter
FLIR ITC – Infrared Training Center
Vi tilbyr FLIR ITC kurs. ITC er verdens største og ledende leverandør av infrarød opplæring og sertifisering, og internasjonalt anerkjent blant bransjefolk. ITC tilbyr et stort utvalg applikasjonsfokuserte kurs fra nybegynnere til eksperter, slik at studentene aldri trenger å nøye seg med et kurs som bare oppfyller noen av deres behov.
Certification Courses
Professional Courses
- Professional Optical Gas Imaging
- Professional Building Inspection
- Professional Industrial Inspection
- Professional Furnace Inspection
- FLIR industrial R&D Measurements
- FLIR advanced R&D Measurements
ITC Category 1 Thermography Course
This course prepares the student for qualification as a cat. 1 certified thermographer. The participant will learn about the basics of infrared, how to operate an infrared camera under different conditions and for various purposes, how to appropriately judge a measurement situation in the field and how to identify potential error sources. After the course, the participant will be able to undertake infrared inspections following written guidelines and to report the results of this inspection.
Course content: Introduction to thermography, camera operation, basic physics of heat, basics of infrared physics, thermal pattern recognition and infrared applications, infrared temperature measurement techniques, qualitative and quantitative thermography, inspection routines and reporting, several hands-on laboratory sessions, examination. The content of the course complies with the requirements of ISO 18436-7.
During the seminar, students will produce a small case study based on the laboratory exercises to be presented to the class.
Pre-requisites: Familiarity with the basic operation of an infrared camera; recommended experience of thermography according to relevant standards
Duration: 35-40 hours (4-5 days)
Kontakt oss på firma@elma-instruments.no eller
22 10 42 70 så finner vi det rette kurset for deg
ITC Category 2 Thermography Course
This course prepares the student for qualification as a cat. 2 certified thermographer. The participant will learn about topics in infrared thermography to increase their knowledge about infrared physics, heat science and infrared measurement equipment and its application. As a cat. 2 thermographer, the participant is able to provide guidance to cat. 1 personnel in the areas of equipment selection, techniques, limitations, data analysis, corrective action and reporting.
Course content: Thermal science, heat transfer, temperature measurement, infrared science, infrared equipment, applications, several hands-on laboratory sessions, examination. The content of the course complies with the requirements of ISO 18436-7.
During the seminar, students will present a prepared case study to the class. The maximum duration (excluding discussion) is 7 minutes and the maximum number of 7 slides should not be exceeded.
Pre-requisites: Valid cat. 1 thermography certificate; recommended experience of thermography according to relevant standards. The prepared case study is to be presented during the cat. 2 course and submitted toward qualification at the end of the course.
Duration: 40 hours (5 days)
Kursdato: 10-14 juni 2024
Sted: Oslo/Stockholm
Pris: 19.500,-
Sted: Oslo/Stockholm
Pris: 19.500,-
Kontakt oss på firma@elma-instruments.no eller
22 10 42 70 så finner vi det rette kurset for deg
ITC Category 3 Thermography Course
This course is not offered on a regular basis. When an ITC Cat. 3 course is available, all thermographers with vaild ITC cat. 2 certification will be contacted by the ITC in advance.
Kontakt oss på firma@elma-instruments.no eller
22 10 42 70 så finner vi det rette kurset for deg
Professional Optical Gas Imaging
This course is over 3 days and will teach the student how to use a FLIR GF series thermal camera and to interpret the results. The course will provide an understanding of why some gases appear as a visible cloud in a thermal image and the student will learn a basic approach to reporting methods and basic onsite safety.
Course content: Optical gas imaging camera overview and operation, basic thermography, spatial resolution, basic thermal science, basic heat transfer, gas imaging fundamentals, absorption characteristics (VOC`s, CO, Refrigerants, SF6) surveying methods, reporting, safety considerations, laboratory sessions.
Pre-requisites: Basic understanding and knowledge of physical sciences, technical background.
Duration: 21 hours (3 days)
ITC also offers a special customer site course for optical gas imaging.
Kontakt oss på firma@elma-instruments.no eller
22 10 42 70 så finner vi det rette kurset for deg
Professional Building Inspection
This course bridges the gap between infrared thermography, background science and applications. The participant will learn the physical concepts of heat transfer and apply them together with relevant building science. After the course, the participant will be able to undertake qualified building inspections on the basis of existing laws, standards, and regulations.
Course content: Infrared basics, thermal transfer, wall structures, insulating materials, humidity, moisture and the dew point, air leaks, pressure profiles, air permeability, survey methodology, reporting, data analysis, laboratory sessions.
Pre-requisites: Valid Level 1 thermography certificate, infrared-related education and experience, knowledge of building techniques, laptop for calculations and exercises.
Duration: 21 hours (3 days)
Kontakt oss på firma@elma-instruments.no eller
22 10 42 70 så finner vi det rette kurset for deg
Professional Industrial Inspection
This course bridges the gap between infrared thermography, background science and applications. The participant will learn the physical concepts of heat transfer and apply them together with relevant industrial science. After the course, the participant will be able to undertake qualified industrial inspections on the basis of existing laws, standards and regulations.
Course content: Infrared basics, electrical applications (current, voltage, resistance, electrical systems, Ohm’s law, important properties of materials, typical faults, surveying methodology and criteria, safety, voltage limits), industrial applications (bearings, pumps, gears, belts, misalignment and couplings, gaskets, seals, rings, glands, steam traps, furnaces).
Pre-requisites: Valid Level 1 thermography certificate, infrared-related education and experience, knowledge of electrical and industrial basics, technical background.
Duration: 21 hours (3 days)
Kontakt oss på firma@elma-instruments.no eller
22 10 42 70 så finner vi det rette kurset for deg
Professional Furnace Inspection
This course bridges the gap between infrared thermography, background science and applications. The participant will learn fundamental concepts of heat and chemistry, how to set up and operate the furnace camera and to adjust it for environmental conditions related to furnace applications. Laboraty and/or field practice is a key part of this course. Basic inspection procedures will be covered including equipment check-out, route planning, permit requirements, safety practices/equipment and reporting.
Course content: Introduction, working environment (refineries, units, furnaces), general rules, camera set up and operation, on site job organization and related procedures, basics of radiative thermal transfer, principles and limitations of infrared furnace applications, discussion and evaluation of inspection and measurement results, methodology, reporting, laboratory sessions.
Pre-requisites: Basic understanding and knowledge of physical scienc, technical background.
Duration: 21 hours (3 days)
ITC also offers a special customer site course for furnace inspection.
Kontakt oss på firma@elma-instruments.no eller
22 10 42 70 så finner vi det rette kurset for deg
FLIR Industrial R&D Measurements
This 2-day course consists of lectures on theoretical subjects, plus hands-on experience and is a customer site course. After a general review of heat and heat transfer, the students will learn about radiative heat transfer and thermography equipment. Intensive practice is provided with software.
Course content: Introduction, review of thermal transfer, radiative heat transfer (includes estimation of TRefl and emissivity with practice), thermography equipment, software (e.g. ThermaCAM Researcher, FLIR Quickplot, FLIR ResearchIR), measurements and software exercises.
Pre-requisites: None, but a basic knowledge of thermography and related areas as well as experience in measurement techniques and general software skills are recommended.
Duration: 14 hours (2 days) - customer site course, group up to 6 persons, plus travel and lodging
ITC also offers a special customer site course for R&D applications, including workshops as well as on-site application support.
Kontakt oss på firma@elma-instruments.no eller
22 10 42 70 så finner vi det rette kurset for deg
FLIR Advanced R&D Measurements
This course consists of lectures on theoretical subjects, plus hands-on experience. After a general review of heat and heat transfer, the students will learn about radiative heat transfer. Starting with the standard measurement situation they will learn about the importance of emissivity and reflected apparent temperature. The students will compute and estimate emissivity and compensate for the reflected apparent temperature. They will also learn about calibration and FLIR's HyperCal software. Depending on the needs of the audience and the time available, additional topics covered may include measurement through windows, measurable figures of merit, signal generation, the influence of integration time, ROIC, etc., triggering and synchronization, non-uniformity correction and bad pixel replacement.
Course content: Thermal transfer, radiative heat transfer, thermal images, the standard measurement situation, computing the emissivity, estimating emissivity and the reflected apparent temprature, figures of merit, triggering and synchronization, measuring through a window, calibration, spectral filters, non-uniformity correction, bad pixels replacement, transient, lock-in and pulse and non-distructive testing. Additional content upon request.
Pre-requisites: None, but a basic knowledge of thermography and related areas as well as experience in measurement techniques and general software skills are recommended.
Duration: 14 hours (2 days) - customer site course, group of up to six persons, plus travel and lodging (additional students on request)
ITC also offers a special customer site course for R&D applications, including workshops as well as on-site application support.
Kontakt oss på firma@elma-instruments.no eller
22 10 42 70 så finner vi det rette kurset for deg
Customer site courses
Many ITC customers find that infrared training at their own facility has many practical and cost-effective advantages, especially in situations where several team members need to attend at the same time. Our instructors will travel anywhere in the EMEA area to deliver on-site courses tailored to a client's applications.
ITC In-house training - group of up to 10 persons (per day)